![TVb AARON](/img/default-banner.jpg)
- 13
- 882 121
TVb AARON
Приєднався 20 лис 2007
how to fix mani pro kupa hand piece kp- 60 - not working ?
This is how i fix kupa handpiece kp-60
Переглядів: 18 675
Відео
How to fix ezviz doorbell won't ring inside the house
Переглядів 7 тис.2 роки тому
How to fix ezviz doorbell won't ring inside the house
how do i fix the dehumidifier with e9 code
Переглядів 58 тис.2 роки тому
How do i fix the dehumidifier with e9 code,
How to fix Sharp 65 4k tv showed logo and turn off
Переглядів 13 тис.3 роки тому
How to fix Sharp 65 inch 4K tv showing logo and turn off. with my experience, happened on most of the other bran name like : Sony, Lg, Samsung, Sharp, Philip, RCA, TLC... Because the Led back lights connect in series, if one of them dead then no power will run through. but why it still can showed logo?! that is the reason most of people thought that leds are still good. welcome any question and...
how to make 8tb HD work on an android tv box?
Переглядів 6193 роки тому
hello you need to have some of the HD partition software to format you HD If you have any question please subscribe my channel I will answare you shortly
How to fix one side not working on bluetooth i7s?
Переглядів 603 тис.5 років тому
How to fix one side not working on bluetooth i7s how to connect i7s bluetooth earphophone Just in case anybody is having issues pairing both, here is how to exactly do it. Step1: Make sure your bluetooth on your phone is turned off. Step:2: Make sure your earpods are turned off as well Step 3: Power up both earpods at the same time by pressing the white button on both until both flashes. Step 4...
H96 pro plus + won’t turn on, blue light , capacitor burned.
Переглядів 15 тис.6 років тому
Happened a lots for those power adapter 5v . There is 1 or two cheap capacitors burned. 10v 1000fu. U can replace with anything higher than 10v but have to the same 1000fu
How to config colour button to work with stb emulator? Button Mapping feature
Переглядів 36 тис.6 років тому
How to config colour button to work with stb emulator? Button Mapping feature
Smart karaoke player with bose l1 model 2, model 1 yamaha mixer, shure beta 87a
Переглядів 20 тис.7 років тому
Smart karaoke player with bose l1 model 2, model 1 yamaha mixer, shure beta 87a. Is it good ?
Gibson Furnace KG6RC 060C 12A Model
Переглядів 9 тис.9 років тому
Gibson Furnace Model:KG6RC-060C How to Fix a Gas Furnace: Furnace Goes On and Off Too Frequently. Air just warm up and the furnace shut off.
How to fix Sony VAIO VPCEE41FD black screen?
Переглядів 87 тис.9 років тому
How to fix Sony VAIO VPCEE41FD black screen? same with most brand name of laptop hp,acer , compag, dell, gateway, .... they all have some model with bad soldier joint on gpu. Hope you can fix your.
Restore Sony vaio to factory image window 8
Переглядів 7 тис.9 років тому
How to Restore Sony vaio to factory image window 8 ?
how to fix dell xps black screen with mouse
Переглядів 10 тис.9 років тому
Dell desktop XPS : Black screen with moveable mouse arrow (F8 restore does not work)
Thank u so much. It worked, you saved my time and money
Fell asleep
Poor fellow needs to get more sleep..
The problem is I have only one airpod so , it says power on power off 😂
It is very difficult to understand him speaking
I tried this method not working for me. The chime is on stable red not even letting me reset it. What do I need to do ?
Open the door bell cover, then reset it
well my sensor was full of dust testing now on a rainy day should be quick to know if it was just the dust xD edit: yup it was just dust in the sensor for me
Thank you - saved me so much aggravation 🙏
Bad video so weird
Thanks a lot. You saved me buying a new one.
Great to hear!
Thanks to you I was able to make this video doorbell work again. You saved me money - thank you sir !
Glad to help
This actually worked!! Amazing. Thank you so much for posting this video. Just a note, so meaning that whenever we do rewiring of the doorbell with mechanical chime, we need to reset and remove it from app and configure wifi to make it work. Anyway!! Thanks again.
Thank you so much.... it worked for me .... heroe
Thx for these instructions. I had trouble getting the wifi to connect when readding the doorbell. After deleting the EZVIZ app and reinstalling it wifi connected ok.
Thank you very much, it helps.
Way too stupid repair!!!!
Thank you for your video. This worked a treat because I had the same problem after a power outage.
you're missing the last washer that lock the bearing in place.
This version doesn't have the end clip washer.
Does this sound like a bad sensor? When my dehumidifier is off and I turn it on, it will work great for about 20 minutes. Then it will stop and show E9. I can then turn it off and back on again. It will work again for about 20 minutes, shut off and show E9. Etc. Also: Yes, it DOES make some water before E9.
It could be the sensor or the freon is low. That is why you need bypass the sensor by connect the pin together. If the sensor pin connected together but it still not make any water then the freon is low. If it made water the the sensor is bad. Hopefully you understand the way to figure what wrong
I kinda get what you’re saying thanks
1). THANK YOU!! 2). Those having difficulty hearing or understanding: Go to settings. Turn on Captions. This will assist. Thank you again.
Deleted the devise and reloaded it but then saw your note that it still will not work unless you reload the type of chime. Works great now. Thanks
It doesnt work
Cant understand a word you are saying
Turn on UA-cam captions to better understand
Difficult time understanding you. But it looks like it would be helpful 🤷
Thanks other video shows replacement of capacitor inside the power supply to resolve non boot issue. Funny thing was that voltage was correct but still not boot. In any case, it looks power adopter is the 1st thing to check.
I am sorry; I can't understand what you are saying. please redo the sound.
Jump the two wires for the sensor.. if you get ice/water your sensor is bad! If you jump the sensor wires and you don't get ice/water your refrigerant is low or empty! Pretty straight forward video that does not need redoing.. you simply need to address your comprehension skills!
@@JaseCJayTurn on Captions to help understand.
@@JaseCJayPlease forgive the stupidity of this question. HOW do I jump the 2 wires? Do I need to solder? Or can I use alligator clips? Thank you
@@FlaschDJ jump the corresponding wires in the white connector plug.. figure it out by looking at the circuit board and tracing back to the connector! A small enough wire to fit in the pin holes in the connector should suffice..
Please how to assemble to take out the broken tip stuck in side ?
This is useless This mumbling fuck
Don’t forget to check the refrigerant. Mine was completely empty.
Thank you. How can I check the refrigerant?
Thanks. Mine had the exact same problem was living with it for about a month. Very inconvenient.
Hi thanks ive tried exactly what you dud but mine still does t chime 😢😢😢😢😢😢 and im an electrician
Make sure you choose the right bell. Also manual test the bell itself by touch 2 wire
Have you waited for 3+ hours after wiring the door bell? If you read the instruction manual there is a small note which says wait for at least 3 hours before first use if you have mechanical chime.
It worked for me. Thanks for posting this. My power went off briefly and caused this problem.
Thank you for sharing this. I had a brief power outage, only several seconds and the ezviz doorbell disconnected from my network. It wouldn't work so I had to do a reset and reconnect my network. Since then the camera and outdoor sensor works, but the indoor chime doesn't work. I will delete the device as you suggest and reset the connection and add the chime back during the set up process. Too bad if you have a power outage. You will have to do this every time. Thank you so much. Bless you
You are welcome. I don’t think the powers out will destroy the setting in memory, but the update does some time, specially when it is doing the update and the power is down
Legit just got these airpods and the left side won't even turn on
Wath the part number?
what is the number of the sensor for buying it to aliexpress
Have you try to bypass it ? I don’t want you to waste money to buy the part
Any explanation of what you were doing, or any material you were using???
Hi. Can any other cord fit the Kupa kp36 hand piece?
F Hisense. Mine lasted about 3 months then e9.
They are built to break
Bonjour ça fait 2 que j achète et fonctionne pas long (1mois) et le code 9 pour quoi ça fait ça et comment régler le problème merci
I got those cam balls dropped off. Could you please show me a video to put those balls on ? Thank you
I wanted to order space parts for this machine but don’t know the part numbers for the spindle and bearings
Im in Canada: www.amazon.ca/Kupa-Original-Manufacturer-Bearing-KP55-60/dp/B07DFF4WRN?pd_rd_w=b2C3I&content-id=amzn1.sym.4e00ab28-1b9c-4741-8535-f6a2139377bd&pf_rd_p=4e00ab28-1b9c-4741-8535-f6a2139377bd&pf_rd_r=210J85FEKMHNBHHWP7YF&pd_rd_wg=AwSj7&pd_rd_r=0740dd25-3c1b-4f65-9b57-5190bda52113&pd_rd_i=B07DFF4WRN&psc=1&ref_=pd_bas_bia_rpt_ba_s_1_sc
What size is the bearing for this handpiece please ?
I sell nail drill bearings! If you wants to buy it. $16 for 2 combo bearings!
Thanks!
WOW, thank you. I have been working with support trying to get my chime inside the house to work. I follow you instructions not expect much..but I've tried everything...and you help me..thanks for your kindness
😃 Im glad to hear that . You are welcome
You should speak clearly men
Right?🤦🏽
Man speek up ...very bad
How many languages do you speak? Do you speak them all perfectly? Do you have any accent?
I am not clear on what fixed the E9 error code. Was it the sensor change or was it a freon refill? TIA for your support.
you bypass the sensor to see if the problem from the sensor, if you bypassed the sensor and your dehumidifier still not make water then you need some freon
What if one's blue and red light not blink after press the button
If a paired device near by it won’t be reset or that earpiece is malfunction
Thanks for the video. At 2:21 you mention that we should try connecting 2 of the sensor pins together. Which 2? Thanks.
Where the thermal sensor connect to the board. The white sensor have 2 wire -just bypass it- make them become 1
Many thanks.